READ ALL INSTRUCTIONS BEFORE USE
Directions for Use
1. Remove compressor and accessory components from carrying case
2. Place compressor so that the rubber feet are resting on a level, sturdy, flat surface where the controls can be reached easily when seated.
3. Remove filter cap, replace filter and reconnect filter cap.
WARNING: Filter must be preplaced before every use. CAUTION: If your hands or fingernails are not strong enough to open the filter cap, use a flat-head screwdriver.
4. Connect tubing to compressor by pushing tube connecter firmly into air inlet connector.
5. Connect tubing to solution cup by pushing tube firmly into place.
6. Open solutions cup by twisting the lid gently counter-clockwise
7. Add solution to solutions cup. Keep upright to ensure no solution is spilled.
8. Reconnect top of solutions cup to bottom by twisting lid clockwise.
9. Attach mask or mouthpiece to solutions cup.
10. Plug into 120V wall outlet.
11. Place mouthpiece in mouth or mask on face.
12. Push On/Off button “On” (I).
13. Inhale deeply and slowly through mouth as aerosol begins to flow, hold for 2-3 seconds, then exhale slowly.
NOTE: If treatment needs to be interrupted, simply press power switch “Off” (0). If using the mask, do not take off mask during exhale. Always sit upright and relaxed when using. This device is rated for intermittent use 30 minutes ON then 30 minutes OFF.
14. Run until solution is fully gone.
15. Push On/Off button “Off” (O).
16. Disconnect plug from wall outlet.
17. Detach mouthpiece or mask from solutions cup.
18. Disconnect tube from solutions cup.
19. Disconnect tube from compressor.
20. In preparation for cleaning the device, open the solutions cup by twisting the lid counter-clockwise, remove the jet cone from the bottom half of the cup by twisting and pulling gently.
Cleaning Instructions
NOTE: After every operation, the nebulizer must be cleaned following the cleaning instructions provided with this device and highlighted below. Please continue with the cleaning instructions before moving forward with the next tasks.
Cleaning the Accessory Parts – Solution Cup and Mask or Mouthpiece
By Completing tasks 15-20 above, there are now 4 total pieces to clean: A mouthpiece or mask, the top of the solutions cup, the bottom of the solutions cup and the jet cone.
Wash all items, except air tube, in a warm water/dishwashing detergent solution. Rinse under warm tap water for 30 seconds to remove detergent residue. Allow to air dry on clean paper towel until all visible water is gone.
Cleaning the Compressor
Wipe outside of the compressor enclosure with a clean damp cloth every few days to keep dust free.
NOTE: Do not use boiling water to clean the accessory parts as this can risk deforming the pieces. WARNING: Do not submerge hands or any other body parts in water over 120°F. At 130°F, water can cause burns in 30 seconds and at 140°F, in just 3 seconds. NOTE: do not towel dry nebulizer parts, this could cause contamination. NOTE: always reconnect the jet cone to the bottom of the solutions cup after cleaning and before returning device to storage as the nebulizer will not work without the jet cone WARNING: To prevent possible risk of infection from contaminated cleaning solutions, always prepare fresh solution for each cleaning cycle and discard solution after each use. WARNING: Keep the outer surface of the air tube dust-free by wiping regularly. Do not submerge air tube in water as it could lead to bacterial growth. Air tube does not have to be washed because only filtered air passes through it. NOTE: Even with regular cleaning and disinfecting, the reusable accessory kit must be replaced every 6 months or risk contamination. NOTE: The nebulizer kit will age after a number of cleaning and/or disinfection cycles. If you find any discolor or physical change, please replace nebulizer kit with a new one immediately or risk contamination.
22. Once solutions cup top and bottom, jet cone and mask or mouthpiece are dry after cleaning, reconnect the jet cone to the bottom of the solutions cup by pushing it gently on and reconnect the cup top and cup bottom by twisting the cup top clockwise.
23. Once cleaning instructions have been followed, put compressor and accessories components into carrying case
24. Store in Warm, Dry location
Reviews
There are no reviews yet.